BT132G-800D TO-92 YuFeng Microelectronics, original manufacturer of diodes, high-voltage diodes, surface mount diodes, fast recovery diodes, Schottky diodes, low voltage drop Schottky diodes, field-effect transistors, MOSFETs, MOSFET manufacturers, MOSFET production, fast recovery bridge stack, inverter rectifier bridge, rectifier bridge, ESD electrostatic tube, TSS solid-state discharge tube, TVS diode - YuFeng Microelectronics
Categories：Product Subsitution Date：2024-11-07 Hits：466 View »
BTB16-800CW TO-220B YuFeng Microelectronics, original manufacturer of diodes, high-voltage diodes, surface mount diodes, fast recovery diodes, Schottky diodes, low voltage drop Schottky diodes, field-effect transistors, MOSFETs, MOSFET manufacturers, MOSFET production, fast recovery bridge stack, inverter rectifier bridge, rectifier bridge, ESD electrostatic tube, TSS solid-state discharge tube, TVS diode - YuFeng Microelectronics
Categories：Product Subsitution Date：2024-11-07 Hits：458 View »
YFW25N15NF PDFN5*6-8L YuFeng Microelectronics, original manufacturer of diodes, high-voltage diodes, surface mount diodes, fast recovery diodes, Schottky diodes, low voltage drop Schottky diodes, field-effect transistors, MOSFETs, MOSFET manufacturers, MOSFET production, fast recovery bridge stack, inverter rectifier bridge, rectifier bridge, ESD electrostatic tube, TSS solid-state discharge tube, TVS diode - YuFeng Microelectronics
Categories：Product Subsitution Date：2024-11-07 Hits：341 View »
If the copper foil fracture caused by improper operation of the circuit board is not remedied, the cost of scrapping a PCB is not small. Therefore, in order to reduce losses, we can perform flying wire treatment at the copper foil fracture site, that is, connecting the two sides of the fracture with copper wire to connect the circuit. If it is a little detached, it is recommended to use a small knife or other small tool to scrape off the insulation paint on the copper foil, as long as the copper
Categories：Product knowledge Date：2024-11-07 Hits：452 View »
If the copper foil fracture caused by improper operation of the circuit board is not remedied, the cost of scrapping a PCB is not small. Therefore, in order to reduce losses, we can perform flying wire treatment at the copper foil fracture site, that is, connecting the two sides of the fracture with copper wire to connect the circuit. If it is a little detached, it is recommended to use a small knife or other small tool to scrape off the insulation paint on the copper foil, as long as the copper
Categories：Product knowledge Date：2024-11-07 Hits：370 View »
In terms of their conductivity, various substances in nature can be divided into three categories: conductors, insulators, and semiconductors.
Categories：Product knowledge Date：2024-11-07 Hits：412 View »
The N-channel MOSFET has an N-channel region located between the source and drain terminals.
Categories：Product knowledge Date：2024-11-07 Hits：446 View »
In order to solve the problem of MOS transistor heating, it is necessary to accurately determine whether it is caused by the above reasons, and more importantly, to correctly test the power loss of the switching transistor in order to identify the problem and find the key points for improvement.
Categories：Product knowledge Date：2024-11-07 Hits：453 View »
The full name of MOS in English is MOSFET, where the suffix FET stands for Field Effect Transistor.
Categories：Product knowledge Date：2024-11-07 Hits：507 View »
Stability refers to the degree to which the parameters of an inductor coil change with environmental conditions
Categories：Product knowledge Date：2024-11-07 Hits：397 View »
